Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Flatbush Homeowners
Water gets into Flatbush chimneys from the top down, and it shows up as crumbling mortar joints, a loose brick at the shoulder, or a rusted damper you can’t open. Masonry around here takes a beating from freeze-thaw cycles between December and March, when meltwater on a south-facing stack refreezes after dark and pushes brick faces off a little more each season. Our technicians have up to 9 years of experience reading exactly that kind of damage, and we inspect before we recommend, so you see the photo of the cracked crown before anyone quotes you a rebuild. We answer 24/7 at (866) 937-7157, with fast dispatch from 7am to 7pm, Sunday through Friday.
What Our Chimney Repair Service Includes
Mortar Repointing
Repointing means cutting out the failed mortar between bricks and pressing in fresh mortar that matches the original composition, rather than smearing a skin of new material over the joint. You need it when joints have receded a half inch or more, or when a screwdriver pushed into the mortar crumbles it. We rake the joints to a proper depth and match the mortar mix to the brick, which matters on the older masonry found across Flatbush because a hard modern mortar against soft antique brick will spall the face.

Spalling Brick Repair
Spalling is the front face of a brick popping off, leaving a rough, porous core that soaks up water faster than the original surface. It almost always follows a freeze-thaw cycle on saturated masonry, which is why we look at the top of the stack and the flashing line first. We cut out the failed units and set replacements with a mortar that lets the wall breathe, then address the moisture source so the new brick doesn’t go the same way.

Chimney Waterproofing
A breathable masonry water repellent keeps liquid water out of the brick while letting vapor escape, so the wall dries from the inside out instead of trapping moisture behind a sealed skin. It’s the right call after any repointing or brick replacement, once the mortar has cured. We apply it to the full exposed stack above the roofline, not just the visible front, because the back and sides take just as much weather.

Flashing Repair
Flashing is the metal where the chimney meets the roof, and it’s the most common leak point on any Flatbush house. When the step flashing pulls away from the masonry or the counter-flashing is missing, water runs straight down into the attic framing and shows up as a ceiling stain a floor below. We reset or replace the flashing and cut a proper reglet into the brick so the top edge sheds water rather than sitting under it.
Chimney Rebuilding
When the top courses of a stack are too far gone to repoint, we rebuild from a sound course upward, resetting or replacing brick and casting a new crown at the top. This is the repair for a chimney that leans, has a visible bow, or has lost enough material that a sweep can’t safely work on it. Rebuilds follow the original footprint and height so the roofline stays consistent with the rest of the block.
Tuckpointing
Tuckpointing is the finer version of repointing: a deliberate, often contrasting mortar finish that highlights the brick pattern on a visible facade. Homeowners ask for it on front-facing chimneys where appearance counts, and it’s also a legitimate structural repair when done to the same depth standards as standard repointing. We treat it as masonry work, not decoration, and we’ll tell you plainly when standard repointing will serve you better for less.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Repair
We work with DuraFlex flexible liner systems for retrofits and repairs, which lets us run a correct liner through older Flatbush chimneys that have offset flues or a footprint too tight for a rigid section. DuraFlex is one of six professional-grade brands we source and install, alongside HeatShield, Gelco, Olympia Chimney, Famco, and Copperfield. When a liner has failed at a joint or the clay tile has cracked, we know where those systems wear and what it takes to restore them.
HeatShield resurfacing is the other brand that comes up on repair calls again and again. It rebuilds the inside of a liner as a structural lining rather than a patch, and we use it when a full liner replacement isn’t necessary. Gelco and Famco caps and Olympia Chimney components turn up on roofs across the neighborhood, and we service that equipment and know how it holds up. Whether you have DuraFlex, HeatShield, Olympia Chimney or any other make, we can help.
Signs You Need Chimney Repair Right Now
- Crumbling mortar in the joints. If mortar recedes or powders when touched, water is already getting behind the brick and the joints will keep failing through the next freeze. Repointing early costs far less than rebuilding a stack later.
- White staining on the brick. That chalky bloom is salt drawn to the surface by moisture moving through the masonry. It’s a sign the wall is staying wet, and it usually points to a failed crown, flashing, or a missing cap.
- A ceiling stain or damp patch near the chimney. Water finding its way inside almost always enters at the flashing line or the crown. Left alone, it rots framing and insulation, and it’s the kind of damage a homeowner can’t see until it’s expensive.
- Rusted damper or firebox metal. Rust means moisture is reaching the interior of the chimney, not just the outside. That moisture also corrodes the liner, and a compromised liner is a fire and carbon monoxide concern.
- A piece of brick or mortar on the roof or in the yard. Falling masonry means the stack has lost structural integrity somewhere above the roofline. Stop using the fireplace until it’s inspected.
Our Chimney Repair Process – Step by Step
- 1
Book the visit and confirm the scope. We ask what you’re seeing (a stain, a smell, a loose brick) so the right technician comes prepared. A flat-price sweep or repair quote is agreed before booking, so there’s no surprise on the day.
- 2
Inspect the full system. We work from the firebox up: damper, smoke chamber, flue, crown, cap, and the exterior masonry and flashing. A camera run through the flue shows the liner’s condition, and we photograph what we find so you can see it.
- 3
Show you the evidence and explain the options. Nothing gets recommended you can’t see for yourself in the photos. Where HeatShield resurfacing will do the job, we say so rather than quoting a full liner replacement, and we tell you plainly when a repair can safely wait until spring.
- 4
Do the work with the right materials. Repointing, brick replacement, flashing, waterproofing, and rebuilds are matched to the masonry and the climate. Liner work uses DuraFlex where a flexible system is the correct fit.
- 5
Clean up and walk you through it. We leave the work area clear and show you finished photos of the repair, plus a written record of the system’s condition. That record is useful when you sell, insure, or schedule the next inspection.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Repair Cost in Flatbush?
Chimney repair in Flatbush typically runs from a few hundred dollars for localized repointing up to several thousand for a rebuild of the stack above the roofline, depending on how much masonry has failed. A typical mortar repointing job runs $400-$900 depending on how many joints and how high the work goes. Spalling brick repair with replacement units usually falls in the $500-$1,200 range, and waterproofing the exposed stack runs about $300-$700. Flashing repair is commonly $350-$800 depending on the roof pitch and how much metal gets replaced. A partial or full chimney rebuild above the roofline is the larger job, typically $2,500-$8,000 depending on height and access.
What moves the price: the height of the stack, whether scaffolding is needed, the condition of the brick underneath the failed mortar, and whether the repair is above or below the roofline. To avoid overpaying, don’t accept a rebuild quote without seeing photos of what’s actually failed, and ask whether resurfacing with HeatShield is an option before agreeing to a new liner. Your written estimate sets the final price, and you get a camera inspection and photo report as part of it. Call (866) 937-7157 for an exact quote. Estimates are free.
Chimney Repair Near Flatbush – Our Service Area
We work on chimneys throughout Flatbush and the surrounding neighborhoods. Homeowners in Kensington, East Flatbush, Flatlands, Crown Heights, Midwood, and Prospect Heights call us for the same masonry failures, and the rowhouse stock across those areas shares the same vulnerabilities. For nearby coverage, see our chimney repair page and our chimney repair coverage in East Flatbush. We also serve Borough Park, Park Slope, Brownsville, Marine Park, and Mill Basin. Dispatch runs 7am to 7pm, Sunday through Friday, and we’re closed Saturday. Book ahead where you can, and call us first if a chimney problem shows up suddenly.
Serving Flatbush, NY – Our Local Coverage Area
We serve Flatbush and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Repair in Flatbush
Chimney repair covers the masonry, metal, and liner work that keeps the whole system safe and weathertight, from repointing mortar joints to rebuilding a failed stack. It’s distinct from sweeping, which removes soot and creosote, and from inspection, which documents condition. Most repair calls start with an inspection so we know what’s actually wrong before quoting. Full details are on our chimney repair page, and you can reach us at (866) 937-7157.
Most localized repairs finish in a single visit; repointing a stack or replacing flashing typically takes a few hours. Larger jobs, like a rebuild above the roofline or a liner installation, usually run one to three days depending on weather and access. We give you a realistic timeline with the written estimate, not a guess on the day.
Typical repair work in Flatbush ranges from about $300 for waterproofing up to several thousand for a rebuild, with most common repairs falling between $400 and $1,200. The written estimate sets the final price, and a camera inspection and photo report come with it. Call (866) 937-7157 for an exact quote. Estimates are free.
Yes. We install and service DuraFlex flexible liner systems, HeatShield resurfacing, and Olympia Chimney components, along with Gelco, Famco, and Copperfield products. Because we work across those brands, we can match the repair to what’s already in your chimney instead of defaulting to a full replacement. Call (866) 937-7157 and tell us what’s installed.
Yes, same-day repair is often possible when you call early in the day. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday; we’re closed Saturday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Call (866) 937-7157 to check availability.
We stand behind our workmanship, and the material brands we install carry their own manufacturer coverage. The specifics for your job are written into your estimate so you know what’s covered before work begins. If something isn’t right after the job, call us at (866) 937-7157 and we’ll take a look.
Clear access to the fireplace and the hearth, and make sure we can reach the roof or the exterior stack. If you’ve noticed a leak, a smell, or a stain, note where and when it appears, because that detail helps us find the source faster. Have any prior inspection reports or paperwork handy. Call (866) 937-7157 to schedule and we’ll confirm what’s needed.
Schedule Your Chimney Repair Service in Flatbush Today
If your chimney is showing failed mortar, a damp stain, or a loose brick, don’t wait for the next freeze to make it worse. Call (866) 937-7157 to book a repair visit in Flatbush. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. You’ll get a camera inspection, a photo report, and a written estimate with no obligation, so you decide with evidence in hand.
Written by the team at Chimney Sweep Flatbush.